This setting out calculator turns design coordinates into the two numbers a total station actually needs: the angle to turn from the backsight and the horizontal distance to the point. Enter the station and the backsight, paste the points to be set out, and you get a bearing, an angle and a distance for each one — with the circle reading you would see if the backsight is set to its own azimuth, and the turn order that keeps you working round the site in one direction. Angles can be read clockwise or anticlockwise, and adding the two heights gives the slope distance and the vertical angle as well. Metres or feet, all in your browser.
Easting first, then northing — the order a coordinate list is always written in. The backsight may be a target on a known point, or the reference object the instrument was zeroed on. If you have the backsight's own bearing instead of its coordinates, type the bearing into the field below and leave the point blank.
The four heights are optional and only affect the slope distance and the vertical angle. Leave them empty and the calculator works in plan, which is what the horizontal angle and the horizontal distance need. Fill the two levels and it also tells you what to set on the vertical circle.
| Point | Bearing | Angle to turn | Circle reading | Distance |
|---|
Drawn from the coordinates you entered. The dot is the instrument, the hollow square is the backsight, and each numbered circle is a point to set out. North is up, so the angle on the drawing is the angle on the instrument.
With eastings to the right and northings up, the direction from the station to a point is
atan2(ΔE, ΔN), measured clockwise from north — which is exactly the whole-circle
bearing a total station displays. The wrap to 0–360° is the only adjustment needed. Note the
argument order: ΔE first. Swapping it is the single most common way to get a bearing
that is right in two quadrants and wrong in the other two.
The horizontal distance is √(ΔE² + ΔN²). Both figures come from the same two
subtractions, so they cannot disagree with each other, and they cannot disagree with the distance
and bearing the reverse calculation would give.
The instrument is oriented on the backsight, so what matters is not the point's bearing but the
angle between the backsight direction and the point direction:
angle = bearing(point) − bearing(backsight), taken modulo 360°. Turn clockwise and a
positive angle is a right turn; read the instrument's left-angle scale and the same turn is
360° − angle. The calculator reports the side you select and labels the column, so
the number always matches what the instrument will show.
Many surveyors do not turn angles at all: they set the horizontal circle to the backsight's bearing (or to zero) and then read the point directly. That is why the table has a circle reading column. If the circle is set to the backsight azimuth, the reading at the point is the point's own bearing — turn until the display shows the bearing in the table and the scope is on the point. The two methods give the same stake; the column just saves a subtraction in the field.
A total station measures a slope distance, not a horizontal one. If you fill in the station level
and the design level of the point, together with the instrument and target heights, the vertical
difference is ΔH = (level(point) − level(station)) + (instrument height − target height)
and the slope distance is √(horizontal² + ΔH²). The vertical angle is
atan2(ΔH, horizontal). Leaving the levels blank keeps the whole calculation in plan,
which is what the horizontal angle and distance need anyway.
Station at (1000.000, 2000.000), backsight on a target at
(1000.000, 2100.000). The backsight is due north, so its bearing is 000.0000°.
A point at (1050.000, 2000.000) is 50 m due east: bearing 090.0000°, distance
50.000 m, and the angle to turn is 090.0000° clockwise. With the circle set to the backsight
azimuth, the instrument reads 090.0000° — the bearing itself.
A second point at (1030.000, 2040.000) is 30 m east and 40 m north. Its bearing is
atan2(30, 40) = 036.8699° and its distance is 50.000 m — the 3-4-5 triangle, which
makes this a good example to check by hand. Turn 036.8699° clockwise from the backsight.
Now the same point with the instrument 1.500 m above the ground and the target at 2.000 m, the
station level 100.000 m and the design level 100.500 m. The vertical difference is
(100.500 − 100.000) + (1.500 − 2.000) = 0.000 m, so the slope distance equals the
horizontal distance and the vertical angle is 0°. Change the design level to 101.000 m and the
difference becomes 0.500 m: the slope distance grows to 50.0025 m and the vertical angle to
0.5730°.
| Method | What you do at the instrument | What the calculator gives | Where it is used |
|---|---|---|---|
| Turn the angle | Zero on the backsight, turn until the horizontal circle reads the angle | The angle to turn column | The default in most work, and the only option on a theodolite |
| Set the circle to the azimuth | Set the horizontal circle to the backsight bearing on the backsight | The circle reading column — the point's own bearing | Total stations, and any job with more than a few points |
| Left angles | Read the anticlockwise scale | The same column, computed on the other side | Instruments and regions whose convention is left |
The three methods produce the same stake on the ground. What differs is the number you read at the instrument, so the only real risk is comparing the wrong pair — a right angle from the table against a left reading on the display.
Set up over the station, sight the backsight, and either zero the horizontal circle on it and turn the angle the calculator gives, or set the circle to the backsight's bearing and turn until it reads the point's bearing. Then measure out the horizontal distance along that line — or the slope distance if the point is not at the same level — and mark it.
A bearing is measured from north and belongs to the point. The angle to turn is measured from the backsight and belongs to the instrument's setup. The two are equal only when the backsight happens to sit due north; in general the angle is the point's bearing minus the backsight's bearing, modulo 360 degrees.
Use whichever your instrument is set to display, and say which in the field book. The calculator computes on the side you select, so its column always matches the display. Right angles are the commoner convention, but instruments configured for left angles are still in daily use.
Fill in the station level, the design level of the point, and the instrument and target heights. The vertical difference is the level difference plus the instrument height minus the target height, and the slope distance is the hypotenuse of that difference and the horizontal distance. Leave the levels blank and the calculator stays in plan.
Because the bearing comes from the two coordinates, and computing it removes a transcription step: the answer cannot disagree with the coordinates on the plan. If you already hold the backsight bearing, switch the backsight field to "a bearing I already know" and type it instead.
It is what the horizontal circle displays at the point when the circle has been set to a reference direction. Set it to the backsight's bearing and the display at each point becomes that point's bearing, so you can turn until the reading matches and the scope is on the mark. Many total stations let you type the backsight azimuth in directly, which is faster than turning angles.
The trigonometry is exact to the precision of the coordinates you enter. The limit is the control: coordinates rounded to the nearest millimetre give the bearing and distance to a millimetre, but a station set 20 mm off the mark moves every point 20 mm. Check the setup against a third known point before setting anything out.
Yes, free, no login, no account and no usage limit. Every calculation runs locally in your browser, so no coordinates are uploaded anywhere.
A setting out calculator is arithmetic, not a substitute for a check. Every figure here assumes the station and the backsight are where you say they are; if the control is wrong, the angles will be consistent and consistently wrong. Measure a known distance to a third point before you set anything out, and compare the reading with the calculated one. About · Privacy & cookies · Terms of use · Developers